|
| clampy |
|
||
|
where is the idle screw or u mean adjust the throttle cable
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
throttle body butterfly screw is behind the lever where the throttle cable connects to
|
||
| Top | |
||
| clampy |
|
||
|
ahhh ok so screw itout a bit or in???
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
clampy wrote: ahhh ok so screw itout a bit or in??? what do you want it to do? |
||
| Top | |
||
| clampy |
|
||
|
i want the revs to drop between gear changes
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| krisisdog |
|
|||
|
Well der, but do you want to raise the idle or lower it with the ISC disconnected?
In to up the idle Out to drop the idle |
|||
| Top | |
|||
| clampy |
|
||
|
isc is connected amd i guess out ....
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| tapper21 |
|
||
|
My EA did the same thing. It has an EL XR6 engine in it with EL XR6 ecu and it has been chipped for the manual tune. Revs would also hang at around 2500rpm after I took my foot off to change gear, even if I was coasting at 60 the revs would keep changing without me moving the accelerator. I unplugged the ISC and turned up the base idle, worked fine ever since. Eventually I will put a blank gaset in there and plug it back in (just to keep everything tidy without hanging cables), but no need any time soon.
_________________ 87 EA S pack
|
||
| Top | |
||
| clampy |
|
||
|
so where is the isc
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| TROYMAN |
|
||
|
the isc is on top of the throttle body..
|
||
| Top | |
||
| clampy |
|
||
|
ok too easy
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| FORDom |
|
||
|
my cars got the j3 chip running in it, with a ef xr6 tickford manual tune..
I've left it for about 300km's but i can't see it fixing itself, should i buy the tuner or simply make this new gasket? |
||
| Top | |
||
| raff-26 |
|
|||
|
I've had that problem before, was a factory manual EB2 wagon
I had pedal box replaced (cracked and flexing), Firewall welded (cracked), New clutch cable and fork assembly- it fixed the issue. I believe it is due to the cable clutch setup- even a god damned HT Monaro had a better clutch setup...and to think Ford used it till 2002.....disgrace.  and yes, it will wear out clutch material quicker
_________________ EF Ghia 5L V8 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
FORDom wrote: my cars got the j3 chip running in it, with a ef xr6 tickford manual tune.. I've left it for about 300km's but i can't see it fixing itself, should i buy the tuner or simply make this new gasket? did you make sure the connections on the j3 port were clean before you fitted the chip?? as if there is the slightest lack of connection the j3 wont do what its suposed to... |
||
| Top | |
||
| clampy |
|
||
|
i had a new clutch pedal box and fire wall re enforced and it still hanging the revs....
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 88 guests |
