|
| xafalcon |
|
||
|
I'm doing a SEFI 5.0/BTR95 conversion into an older car with a mechanical speedo. How do I get the electronic speedo signal to the transmission computer so the shift points etc are correct? Is there a speedo drive splitter (or similar) that will allow me to run the electronic sender (for the TCM signal) and a cable drive speedo? Or something that runs off the driveshaft?
Thanks in advance
_________________ XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual |
||
| Top | |
||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
how hard would it be to put an electronic speedo mechanism in the dash? imo thats your best option.
_________________ T.I. Performance - Ford Performance Parts & Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts, Haltech ECUs and more! |
|||
| Top | |
|||
| PIMP_LTD |
|
||
|
I was in a similar boat with my old P6 LTD. It has a factory 351 and FMX, and i wanted to fit a BTR into it. I heard there was some Y piece that goes into the box and gives 2 outputs, but i never found any other info on it.
So i decided to give up on it and just rebuild the FMX.
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| xpvanman |
|
|||
Age: 58 Posts: 252 Joined: 22nd Mar 2008 Ride: BF F6 Typhoon. XP Van.XF Hearse Location: Newcastle |
Have a talk to your local instrument technician that rebuilds car speedo & guages - They usually sell the adaptors to do this job. A mate put a big block Chev & 4L80E into a 66 Chev & the local speedo & guage repairer steered him in the right direction with that conversion...
|
|||
| Top | |
|||
| xafalcon |
|
||
|
Yep, I've already tried the local speedo shop and he was of little help. Never even herd of anything like a splitter or piggyback sender.
I've pulled a speedo sender apart to see how easily it could be modified but it's not a simple job. Then I thought about using a variable oscillator based on a TPS signal but that's not really the solution either. Someone out there must have found a source of such a piece, or a modification that is relatively easy or a simple circuit that emulates the signal - anyone??? thanks again
_________________ XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual |
||
| Top | |
||
| Matt_jew |
|
||
|
Castle Auto Electrics on Victoria. They have T piece adaptors that drive the electronic sender from the end and the cable at 90 degrees.
_________________ xr6turnip wrote: More people paid for a ride in a VT commodore then an AU Falcon so the VT is superior.
Based on that fact my Mum is the best around! |
||
| Top | |
||
| xafalcon |
|
||
|
Thanks for that, have you used one yourself or know of somebody who has?
I've also thought about welding on a second speedo connection point below the factory one. This should give the opposite rotation that I need for the mechanical speedo. Cheers
_________________ XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual |
||
| Top | |
||
| xafalcon |
|
||
|
Never heard back from Castlemaine....
Anyone else have any sources? Thanks
_________________ XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 99 guests |
