|
| ef_falcon_95 |
|
|||
|
teeroy wrote: i have a torque converter and flywheel you can have for the costly price of shipping and a box to fit them, just done a 5 spd conversion, my auto was shagged. flywheel and converter looked fine. I'll be getting a torque converter and flywheel with this box , but if I end up needed them ill let u know Cheers
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
So the s3 and s4 shift kit u cut the 2 wires at the ecu and earth the ecu side with resistors. Can't remember which one though .
If its better on boost ill go with that one . Less wiring when I install the box .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TROYMAN |
|
||
|
yep....
the info is pretty easy to find.. although i would have it on a switch so when your just cruising around off boost you can turn it of.. |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Would the resistors still effect it on a switch ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Its a 27 ohm 5w resistor One on each solenoid at the ecu side .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TROYMAN |
|
||
|
ef_falcon_95 wrote: Would the resistors still effect it on a switch ? not if you wire up to a 6 pin duel throw switch, position1 joins the solinoid to ecu=off, position2 joins ecu to earthed resistors leaving solinoids disconnected=on.. |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Cheers , seems easy to wire up .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Found this c4. Says its built to handle 650 Fwhp.
What's that in rwkw ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| MAD |
|
|||
|
Depending on drivetrain losses, but a rough estimate is about 380rwkw. (Based on 25% loss.)
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Got my clutch today , but seeing as I won't be needing it , it's forsale . Asking what I payed for it $215 ono.
_________________ El XR6 Turbo |
|||
| Top | |
|||
| Ef Ghia XR6 |
|
||
Age: 46 Posts: 73 Joined: 16th Jun 2012 Ride: Ef Ghia 1994 Location: Maybe i'm in the fridge ;] |
ef_falcon_95 wrote: Cheers , can they be brought by them selves ? I used a tap washer for the thermostat pipe seal. I'm pretty sure they are the same size from looking at them both.It fitted perfectly (a little tight around pipe but atleast it aint going to leak) and have had no drama with it. Good thing is that they can be bought from any hardware store and cheap. After all it is just a rubber seal so no difference with the tap washer..Probably advisable to buy new water pump but atleast you could use this for future reference if you like.. |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Thanks but ill most likely but a new water pump . Only $35
_________________ El XR6 Turbo |
|||
| Top | |
|||
| Ef Ghia XR6 |
|
||
Age: 46 Posts: 73 Joined: 16th Jun 2012 Ride: Ef Ghia 1994 Location: Maybe i'm in the fridge ;] |
ef_falcon_95 wrote: Thanks but ill most likely but a new water pump . Only $35 No worries,here a link to what i mean if your still unsure...http://www.fixatap.com.au/cat/sink-and-basin-fittings |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Cheers
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
not much to update on. hopefully get a auto box soon.
This is the New hog .  And this to power it http://pages.ebay.com/link/?nav=item.vi ... 0926138000 Won't have a licence from august to November . So this is my ride . So I have 3 months where the car won't get driven so could be a perfect time to fit all the turbo gear on get it tuned then take it off when I get my licence back.
_________________ El XR6 Turbo |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 6 guests |
