|
| ef_falcon_95 |
|
|||
|
Nah no other engine . Hoping this one will not go bang lol it's its good condish, afaik rings are good , it blows no smoke . Head gasket was changed recently .
I didn't get the purple one , turned out it was fake. I got a silver one , hopefully I get it today . I'm keen to cut off the old flange , weld on the tial flange to the manifold . Then I can bolt up the dump pipe . Put some oil in the engine , start it . Admire it spooling lol..then dump the oil and check for leaks . Only using hombrand oil for a flush and leak test . No point using good oil then it leaks everywhere .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Found some rubber ds 2000 hose at work . I can use it to extend the feed and make up a drain . It's flexible and can hold a lot of pressure .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
rubber hose will get hot go brittle and crack .use silcone its better . or teflon braided one mate
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I'm not sure if its rubber just guessed ,it's hydraulic hose so its suitable for hot oil.
It says on it fire resistant . Should be ok ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TROYMAN |
|
||
|
make sure its oil resistant Fluro-Silicon Lining hose, i had a minor engine fire from using normal silicon hose as a drain..
and dont skimp on the feed line, last thing you want is a presurised oil leak that can destroy everything..lol |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Hose is d600.
Feed hose is all hooked up . Just need a new oil sender as I broke it removing it. Didn't have another 1/2 nipple so I couldn't make up a drain hose.     also got my clutch master cylinder 
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Double post
_________________ El XR6 Turbo Last edited by ef_falcon_95 on Thu Aug 09, 2012 7:04 pm, edited 1 time in total. |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
why didnt you run the teflon feed hose all the way to the t piece in the block
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
It wasnt long enough . Too tight over the rocker cover . So I used the black hose to extend it 100 mm .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
arh ok no worries
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Got my waste Gate .
Its missing a flange , not sure which one I'm guessing inlet . The flange I got is sloppy in the clamp hmm.
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
 
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Found out the flange is actually a valve seat , ill have to find flanges on eBay or buy from tail
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I've brought flanges from the US . Hope they turn up next weekend .
Here's my drain 
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
had to shorten the drain, its connected up now.
dump pipe is fitted , just have a issue with the turbo intake. its about 80mm behind the p/s pump and i cannot see how im going to get the silicon reducer on, then the stainless pipe, outlet is easy as i spun the housing around to its pointing upwards. i hate low mount turbo's no room for anything down there 
_________________ El XR6 Turbo |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 7 guests |
