|
| ef_falcon_95 |
|
|||
|
so would it be wrong connecting the signal ground from the interceptor to it ? thats what its got un the wiring diagram.
anyway i grounded it to the ecu ground which holds the ecu to the body, now reads 12v but still unable to open com port, so im installing xp on to a 2nd laptop, if that fails im out of ideas .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TROYMAN |
|
||
|
yes the signal ground ends up grounded through the ecu to the body aswell
|
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
but when i had the ecu ground connected to the signal ground i was only getting 0.10v . ( not 1v that was as guess as i forgot lol)
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
No porn on that laptop .
 My mates putting xp on it for me . My pc knowledge doesn't extend that far lol
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I think I need and external hard drive to dual boot . Running xp isn't an issue. The laptop didn't get used much anyway.
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
This maybe my problem aswell .
Quote: First, make sure the tab on the top where it says "USB" is "Attached". Then what you do is go into the Virtual PC settings and enable your serial adapter as a com port. then you go in your device manager in Virtual XP and set your adapter to the same com port. Go into halwin and make sure the port is the same also. THEN exit Halwin and reopen it. It takes a weird order to make it work. If you have halwin open when you are setting everything up, then it will not communicate until you reopen halwin. Its weird, but Im using it with no problems Maybe if I enable the serial adaptor as a comm port it should connect .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Halla f**k loola
The ecu is connected didn't need xp . Xp mode works . Theres a USB tab up top and I didn't allow the connection. Loaded the base map . Battery is flat so I cannot start it
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
got a jump start and it starts and runs, runs a bit rough in the high rev range but only a base tune,very happy now that everything is working out , going to plumb up cooler piping and fit cooler this weekend ,
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
also got a fitting for my clutch master
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Yea took my mate all day to install xp . You could imagine how he was when I said I didn't need it lol
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I'm still gonna use the laptop with xp . It can be my tuning laptop .
He had to wipe the hard drive because I installed xp over windows 7
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
got pretty much all of the cooler piping done this arvo . ill weld it up on saturday, still have to hook up vac lines, injectors, catch can. if i get all that done it will be boosted this weekend and ready for a tune, only going to run 6 psi , then do the 6 speed conversion later this year.
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Got all the intercooler piping done .
Will it make boost while reving it stationary or only driving ?      
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Searched on google and I thought it may have been due to the engine having no load , which is right .
_________________ El XR6 Turbo Last edited by ef_falcon_95 on Sat Sep 29, 2012 7:19 pm, edited 1 time in total. |
|||
| Top | |
|||
| TROYMAN |
|
||
|
it generally wont make boost free reving, it will under load driving...
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 11 guests |
