|
| B Bear |
|
|||
|
Jesus ! That is rooted !! Engine gore
 Good to see that you aren't giving up on it yet. Where you only running the xr6 regulator before hand ? |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Not giving up yet . Not until I've actually drivin it with good power .
Yup xr6 reg . No one with big power has mentioned that they changed the reg
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TROYMAN |
|
||
|
i ran the std au xr6 reg in my ed...
|
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
But that's 350 kpa isn't it ? Were your injectors at 80% .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| B Bear |
|
|||
|
Fair enough, I decided to replace mine with a rising rate reg.
The turbosmart fpr is a 1:1 with adjustable pressure. The std xr6 reg is 300kpa, unless Troyman was running something else ? AU perhaps ? |
|||
| Top | |
|||
| TROYMAN |
|
||
|
ef_falcon_95 wrote: But that's 350 kpa isn't it ? Were your injectors at 80% . to be fair, yea it was 350kpa.. in the ed the injectors were at 45%. in my au, it had 400kpa reg with 80lb injectors and they were at 30% the good thing about the xr6t 400kpa reg is it also rises at a 1:1 ratio |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
You also had 65 lb Injectors?
So what caused my engine to blow up was the standard reg ? As you can see it leaned out .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
its got nothing to do with the reg mate . mines standard and has more power ,and never had a drama. the retard who tuned ya car is the problem
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| xr6_corbin |
|
|||
|
Mine runs standard ef xr6 reg and never had any dramas. Maybe take it elsewhere for tuning. Especially with your rebuilt motor.
_________________ Just Falcon Around. |
|||
| Top | |
|||
| Matt_jew |
|
||
|
Definately a tune related f**k up.
_________________ xr6turnip wrote: More people paid for a ride in a VT commodore then an AU Falcon so the VT is superior.
Based on that fact my Mum is the best around! |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
I already have the xr6t fuel reg . So may as well use it .
Taking it to jem . Since I've got a month free ill get stuck into it. Need these rods so I can put it back together .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Paid for the rods . Now waiting for them to arrive , should be here Friday or Saturday now that auspost are delivering on weekends . Only until after xmas . Then I can get it balanced and start putting it all back together .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| xr6_corbin |
|
|||
|
Nice, what rods did you end up going with? Are you going to go bigger turbo now that your going to have a strong bottom end? Or just up the boost on the to4e?
_________________ Just Falcon Around. |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I went with spool rods . Just going to up the boost on the to4. I'd like to go a gt 35/82 but ill see what I can get from this turbo first .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| xr6_corbin |
|
|||
|
If you decide to upgrade go a 3788, look at sonic performance they have them on special for $1100 ball bearing units too. Cheap as chips! They're suppose to have the spool rate of a 35 and the flow rate more like a 40. Would be a good upgrade.... Just saying
 http://www.sonicperformance.com.au/7727 ... r_R/pd.php
_________________ Just Falcon Around. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 60 guests |
