|
| mitchell g |
|
||
|
{USERNAME} wrote: It's a good idea but since I'm not plumbing back my catch can oil in the intake isn't an issue you could still get some blow by, process west do it standard, mate of mine doesn't have a catch can on his barra and he gets oil in the bottom of his plenum |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Fair enough ill see what I can do . Some 3mm X 25 mm alloy flat bar should do the trick .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| mitchell g |
|
||
|
easily process west are like a ram tube
|
||
| Top | |
||
| xcabbi |
|
||
|
{USERNAME} wrote: It's a good idea but since I'm not plumbing back my catch can oil in the intake isn't an issue Do you plan on keeping your car emissions legal? I've got my mind in a few of these. http://www.jegs.com/p/JEGS-Performance- ... 3/10002/-1 The plan is one for the pcv and one for the breather(s). That way all your crank case ventilation is legal, and works better than factory. |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
That looks like a better way than plumbing it back .
So the catch can vents to the oil , air separator ? Then that vents clean air to atmosphere ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| xcabbi |
|
||
|
No. You set up 2 oil-air separators. For the first one you run a line from your pcv valve to the separator and then from the separator to the plenum.
For the other one you run a line from the rocker cover breather to the separator and from the separator to the turbo inlet pipe (between turbo and air filter). All of the oil vapour is contained in the washable.filter ellement in the separators and you get no oil residue getting sucked into your air intake . If you feel that you have excessive blow by then by all means add a catch can before each sepator but under no circumstances must it vent to atmosphere, even if it has a filter element on top. The epa likes to a*** rape people with breathers. |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
I get you now . Ill do that then . Since the motor is rebuilt I shouldn't have a need for a catch can then .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| xcabbi |
|
||
|
I thought about building my own until I saw how cheap these are.
|
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
I'm pretty sure we've got those at work lol have a look tomorrow .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| xcabbi |
|
||
|
I thought about building my own until I saw how cheap these are.
|
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
The ba/bf hydraulic pedal setup has arrived . Plan is to drill a large hole in the bracket then tack weld in some tube that will slide over the manual pedal pin on the pedal box . Then secure it somehow to stop it moving .
I brought a bmw clutch master cylinder as it looked very similar to the Ba/bf one , plan was to make my own bracket until I found out it was easier to buy the ba/bf setup Anyway I was going to return the master cylinder until I noticed they are almost identical to each other . Even the holes line up . Out let is the same fitting and so is the Clevis . So I'm keeping it now as a spare . Was only $130 from USA compared to $300 here from ford etc .   Part number for anyone interested 
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Test fitted the plenum. The T/B sits too far forward .
So I cut the front off where the T/B mounts to and make it sit back further . Just have to weld it back together . Hoping I don't have issues with bonnet clearances
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Plenum is all done . Except the top isn't fully welded ran out of gas .
Tomorrow ill get more gas and finish it off Tuesday . Throttle body sits in a good position . Ill need a eb top thermostat housing because ill have issues with the T/b being too close to the top radiator hose .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Top of plenum is welded . Bung for air sensor and vac tee are welded in.
Just have to remove the BBM off my car and bolt the plenum and t/b to it .    
_________________ El XR6 Turbo |
|||
| Top | |
|||
| Matt_jew |
|
||
|
Getting there.
What did the pedal set you back? Im interested in seeing how you go setting it up. The cable clutch in the ute is s**t me no end. Hopefully this may be an option.
_________________ {USERNAME} wrote: More people paid for a ride in a VT commodore then an AU Falcon so the VT is superior.
Based on that fact my Mum is the best around! |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 57 guests |
