|
| dunwood |
|
|||
|
Ok here's a list of items i've got to built up the 418w to a short motor
Scat crank Scat rods ACL race series bearings (Main & conrod bearings) SRP flat top pistons Hastings racing rings Comp Cam solid roller cam Comp Cam roller cam followers Rollmaster double timing chain & gears TCL flywheel Pro Race harmonic ballancer ARP Bolts (Main, conrod & head bolts) Probe girdle kit RTS high volume oil pan Sealed Power high volume oil pump & pickup hope to start building it when i finish work in the next week or so
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| fairlane6970 |
|
|||
|
Mmmm! that sounds nice!
_________________
|
|||
| Top | |
|||
| dunwood |
|
|||
|
Does anyone know if a Ed dash assembly will fit into a EL body? As my dash was burned to a crisp before I got it, I'll want to replace it. I want a ED as they don't have airbags in them. Or is there a EL Dash that dosen't have airbags in the dash?
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| huggiebear |
|
|||
|
EF/EL GLi dash doesnt have the airbags. either do the futura.. unless optioned.
but yes the ED dash will still bolt in but a pain to get the electrics working with the cluster. stick to the loom type |
|||
| Top | |
|||
| dunwood |
|
|||
|
wiring loom's not a issue as i'm making my own
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| dunwood |
|
|||
|
Ok the 418w block arrived this morning, so i'll be able to start assembly of it on the weekend. BTW, does anybody have a EA -> EL dash that they want to sell to me? Don't care about the wiring as it will be entirely stripped out.
Some more news, I'm getting my heads & intake manifold for the engine next week. The heads and manifold are CHI
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| LIMO8U |
|
||
|
pm sent
|
||
| Top | |
||
| dunwood |
|
|||
|
Ok all, here is today's progress
 Rods & pistons go in tomorrow
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| LIMO8U |
|
||
|
good stuff mate. looks good
|
||
| Top | |
||
| dunwood |
|
|||
|
Ok i put the pistons together and installed them today. I also degree the cam also took a while to setup, but i got it right in the end. should have the heads during the week.
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| dunwood |
|
|||
|
Here's more progress
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| dunwood |
|
|||
|
Ok, i've done some more to the motor today.
 BTW, does anybody know where i would be able to purchase Neoprene Rocker cover gaskets for a cleveland heads?
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| dunwood |
|
|||
|
Went to ronza's place yesterday and purchased a spoiler off him for $40. Very happy how it turned out on the car
 I also removed the dash out the car and started to remove the aircon stuff behind the dash  Also got the car to run without the dash by putting the wiring back in.
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| sooty72 |
|
|||
|
{USERNAME} wrote: BTW, does anybody know where i would be able to purchase Neoprene Rocker cover gaskets for a cleveland heads? Felpro, p/n 1616, should do the job for you. VPW or Eagle should have them. 
_________________ Yes, I own a Ute. No, I won't help you move! |
|||
| Top | |
|||
| dunwood |
|
|||
|
Thanks mate, I'll check it out.
_________________ 1968 Mustang Coupe (in progress) |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 103 guests |
