|
| misk_one |
|
|||
|
why would you disconnect the VCT for a turbo setup?
_________________ XG Panelvan |
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
a turbo starts to make torque at or below 1500rpm so there is no need for it really ask troyman why he has his disconnected for his Supercharged VCT motor? Apart from the fact he has a different cam that is non VCT but there is no poing as the torque is made early in the rpm range there for not really needed between 750rpm and 1500rpm?
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| TROYMAN |
|
||
|
the main reason i removed the vct was because there are not many aftermarket cams for vct.
there is only jmm that want stupid prices and another shop that have not had and tested feedback on there cams. i dont like being the test mule for something that could be worse off power wise.. plus the fact that my vct solinoid was weeping oil and a replacement is over $250.. with the supercharger its making 1 psi@1500 rpm so there is still good torque down low, so with all this together i decided to ditch vct and run a wade au1645 cam, which gave me more mid range and top end.. |
||
| Top | |
||
| misk_one |
|
|||
|
i think you would be silly not to keep the VCT with a turbo setup.
your missing the point that any extra torque or power (which will equal exhaust gas) is going to help spool a turbo. seeing as yours is setup and running with the aftermarket cam AND an ECU you can tune, there is no reason to disconnect it.
_________________ XG Panelvan |
|||
| Top | |
|||
| TROYMAN |
|
||
|
misk_one wrote: i think you would be silly not to keep the VCT with a turbo setup. your missing the point that any extra torque or power (which will equal exhaust gas) is going to help spool a turbo. seeing as yours is setup and running with the aftermarket cam AND an ECU you can tune, there is no reason to disconnect it. possably on turbo, for early spool yes! but for supercharged no need as rpm is what gives me boost. and removing the vct cam and fitting an aftermarket cam has so far given me a 20rwkw and 60 rwnm more torque gain over the vct cam.... also i found in my application, that even with the non vct xr6 cam it still performed better overall than it did with vct.. it could be a combination of me using non factory ecu, no sequential injection , all the stuff thats not on an au vct set up..lol.. 
|
||
| Top | |
||
| phillyc |
|
||
|
Please keep the VCT active. The whole point is it advances it 10 camshaft degrees until 2950rpm, then returns it back to the neutral/non advanced state. Advancing a cam gains bottom end and midrange, but sacrifices top end.
I did a couple of dyno runs two weeks ago, and played with the VCT activation using my Sniper tuning. Leaving the cam advanced lost 4% max power - in my case 5rwkw in the top end, but the bottom end was improved. In fact, using the A/F as a guide (because each run had the same commanded A/F) i was able to calculate that at 5500rpm the VE difference was 8%! When in the normal position, it had a higher output over nearly a 1000rpm rev range! If you buy an aftermarket cam and install it in the advanced position without the VCT, you will gain on the bottom end, but lose on the top end. Check out Crescent (site sponsor!) as they are now doing VCT regrinds! Cheers Phil |
||
| Top | |
||
| EDXR6-Poly |
|
|||
|
well i have mad the decision to turbo it and leave it VCT controlled by the RPM switch using the standard cam shaft and the head has been ported so no need to take the head off to modify anything and just putting a turbo kit on it from here
Im thinking about making my own turbo exhaust manifold as there is a few cheap one but dont look like they would be really flow effective http://www.fordmods.com/wanted-ford-parts-f18/wtb-wtb-e-series-turbo-exhaust-manifold-t87990.html but im thinking to keep the log style and build my own and use something along the lines of a t70 turbo and i can get a set of BOSCH 968 440cc FUEL INJECTORS for under 300 and use my J3 to tune is and run the pipework and a stock XR6-T intercooler and run it through the stock airbox setup to feed the intake side of the turbo I'm only hoping to make the 200-220rwkw mark and id be happy to not bother to mod anything else on the car
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| TROYMAN |
|
||
|
yep cms was the one who had no feedback on how the cam performed..
im sure with testing or feed back it could be a great cam but im not willing to go through that.. imo its a lot of effort for such little return.. but honestly the vct engine is good! but if i was to replace mine, next time i would go with a non vct..or just update to bf dohc.. before i supercharged mine there was only 4rwkw difference between the vct and my old non vct hp engine.. |
||
| Top | |
||
| xpression |
|
|||
|
what was the spread of power like? and economy?
|
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
Ok today I got my self a set of BA/BF FPV side repeaters to go into my ED I have a XR6/8 less the wing / bootlip coming from huggiebear (cheers mate) to get painted and if all goes well the car will be getting a respray in the next week but as the weather seems to be playing around I think it might be another month or 2?
So I've started to put a gasket kit through my AU2 motor I got about a week ago to put into my car hence saying that if Im going to change the motor i may as well change it to manual while the motor is out ? I have had the VCT head that I got off (olivexm) ported and shaved 5 thou and did the BBM conversion while I was at it, next up is getting the part together to put the AU2 motor back in the car( I'll be cutting and bending the Box on the front of the K-Frame and grinding a little off the front of the sump) with a manual (t5) and regas the A/C system (its very cold as it is but dammit I need a serp setup to run the S/C)i can get that done locally for $210 includes labour, dryer and gas, the next step is getting the Raptor S/C kit from Raptor Superchargers (hehe) it will be installed on the motor once its back in the car. Then the fun starts getting the tune done on it as ill be making another trip to mackay or rocky depending on where seems to be better at tuning S/C I6 motors? well thats all I have got to doing so far ill keep you updated
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| JoeXR6 |
|
||
Age: 43 Posts: 387 Joined: 30th Nov 2007 Ride: AU111 XR6 VCT Supercharged Location: Brisbane |
Sounds good. Why have you chosen SC over turbo?
_________________ FOR SALE! - Supercharged AUIII XR6 VCT, intercooled, T5, big brakes.... details in the 'For Sale' section - ford-parts-for-sale-f17/fs-supercharged-au-xr6-vct-series-iii-intercooled-rwc-rego-t114254.html |
||
| Top | |
||
| EDXR6-Poly |
|
|||
|
More for the fact like TROYMAN and what others have said how easy it is to install and uninstall and the driveability and it can be removed and take the J3 chip out and you have a N/A car again in a few hours yet a turbo seems to be alot of work to convert back to N/A
Im not after trye shredding power from 0-200kph just something to get it going a little better on the open road (overtaking etc) but to also keep it as a daily too How have you found your S/C VCT what boost and setup did you use? ECU? etc?
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
bit of an update with A FEW PICS i got my wheels sandblasted and painted Black i think they look good also got the door mouldings re painted too aswell as a pic of the now BRAIDED OIL LINE for the VCT unit
   
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| 4LEDboy |
|
|||
|
Is that a genuine XR6?
_________________ Adelaide Motorplex < Click on it! You know you want too! Quote: Thats not the point *a**hole
|
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
Yes with the 18335 body code and all !!!
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 80 guests |
