|
| Lowlane7 |
|
||
|
Attachment: BigBlock_opt.jpg Attachment: stripping2_opt.jpg Attachment: stripping_opt.jpg The lowlane hiding under a pile, waiting for its smartlock bypass module so it can come back to life again Attachment: buried_opt.jpg Attachment: EL_opt.jpg
You do not have the required permissions to view the files attached to this post.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| Wacko.Jacko |
|
|||
|
my lowlane project after my ex burnt out my last one barra to t5 instead of ed 4.0 sohc this time, do you have any good sources for manual parts? need barra to t5 bell clutch cable clutch kit clutch pedal box and gearstick seal if you know where i can get them cheep
You do not have the required permissions to view the files attached to this post. |
|||
| Top | |
|||
| Lowlane7 |
|
||
|
{USERNAME} wrote: my lowlane project after my ex burnt out my last one barra to t5 instead of ed 4.0 sohc this time, do you have any good sources for manual parts? need barra to t5 bell clutch cable clutch kit clutch pedal box and gearstick seal if you know where i can get them cheep Nice project. Id love to do a barra conversion, but the EL XR6 was more readily available. For the pedal box, I would look at the Mal Wood pin kit, so much easier than taking the dash apart.. Im not too sure if the BA had the same T5 as the EL's or if the earlier T5 will bolt up. But a wreckers would be best option for parts, or find a crashed manual and pilfer all the bits you need off that.. What color are you gonna paint it?
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| Wacko.Jacko |
|
|||
|
big single 3-4 inch stainless pipe
|
|||
| Top | |
|||
| Lowlane7 |
|
||
|
My street cred just went through the roof!!!
 Lenso D1R 20x8.5 with 245/35 front 20x10 with 285/30 Rear Had to grind some of the edge off the top ball joint knuckle to make the bigger tires fit. Currently doing more measurements to see if I can put on come bolt on 20mm spacers to push them out to clear and to add another 165% awesomeness to the stance as well. Definitely needs spacers on the rear to bring them out and fill the guard more. Rolled the front gaurds already, and ill do the rears later but dont really need it with the stock height. Attachment: 20161218_173550.jpg Attachment: 20161218_173613.jpg Attachment: 20161218_173622.jpg Attachment: 20161218_173631.jpg
You do not have the required permissions to view the files attached to this post.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| Lowlane7 |
|
||
|
The grinding took about half the depth of the upper ball joint clamp on the underside of it. Ill be regularly checking it if it starts to crack or let go, I know the AU's have a habit of dropping the ball joint just normally so I dont want it falling apart on me at all.
Attachment: 20161218_173652.jpg Attachment: 20161218_173716.jpg Attachment: 20161218_173734.jpg
You do not have the required permissions to view the files attached to this post.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| Lowlane7 |
|
||
|
Also the newest addition to the collection...
XD S-Pack 6cyl Single Rail 4 speed Trying to track down the original owner because this body kit is pretty unique. Apparently its a d**k Johnson Special, the rims are 2 piece Enkei AMC wheels. Attachment: $_20.JPG Attachment: $_20 (4).JPG Attachment: $_20 (8).JPG Attachment: $_20 (6).JPG Attachment: $_20 (7).JPG
You do not have the required permissions to view the files attached to this post.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Majestic-12 [Bot] and 5 guests |
