|
| Lay3d_low |
|
|||
|
huggiebear wrote: there isnt lack of interest.. there is lack of companies caring lol im just going to find a set of adaptors cheap and use them. stuff what the cops say, they bolt on so they are just as safe as any wheel... yeh thats what im thinkng of doing. i was just gonna paint the adaptor the same colour as inner side of wheel, make it blend abit.
_________________ Sexy Xe |
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
well its been a week already since i started the roof liner, and still havnt progressed
 have no money to continue with it, but good news is that i have got some seats on the way, as soon as i go back to work and get payed hahaha. mean while i finaly sorted things out with a guy on ebay about a head deck i bought, and it was sent this morning so it should be arriving in next few days and that will be installed the day i get it more then likly lol  other then that, not much to report. although i wana do the reaf leaf mod to lower it, but im not sure on how to do it, all i know is pull out leaf an flip it this way an put it there lol.
_________________ Sexy Xe |
|||
| Top | |
|||
| nato83 |
|
||
|
Lay3d_low wrote: well its been a week already since i started the roof liner, and still havnt progressed have no money to continue with it, but good news is that i have got some seats on the way, as soon as i go back to work and get payed hahaha. mean while i finaly sorted things out with a guy on ebay about a head deck i bought, and it was sent this morning so it should be arriving in next few days and that will be installed the day i get it more then likly lol other then that, not much to report. although i wana do the reaf leaf mod to lower it, but im not sure on how to do it, all i know is pull out leaf an flip it this way an put it there lol. or buy 2.5" lowering blocks from me. lol |
||
| Top | |
||
| Lay3d_low |
|
|||
|
i would but i wana go lower, i been hearing with the leaf mod its only like 30 bucks on few things you make up and you got like 4-5 inch drop, would be good to have that. considering a 2 and half drop in wagon is like making the back sit the same as front almost, only a tad lower.
if they was 4 inch block i would say hell yes but i dont think they make a 4 inch block kit for E series wagon?
_________________ Sexy Xe |
|||
| Top | |
|||
| BenJ |
|
||
|
With the leaf spring mod the two that I know personally that have done have only got around a 2" drop. One of them reports that the rear is now softer than it was before hand.
I have 2.5" blocks in my wagon, and with four adults and sprited driving the tailshaft hits the floor. Something to consider if you want to go real low. BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| Lay3d_low |
|
|||
|
ohk, so you stand by blocks then..i might see if i can get 3 inch blocks or something, i will still study up on the leaf mod but not to say thatll ill do it
_________________ Sexy Xe |
|||
| Top | |
|||
| huggiebear |
|
|||
|
i think the reason why they dont make 4" blocks is because your springs and bolts for it would be like 2" off the ground in a stock car. where legal would be 4"
|
|||
| Top | |
|||
| nato83 |
|
||
|
I only have 2" in the rears now and the clearance underneath is an issue from the u-bolts. Will find out the legalities on Monday when it gets a new RWC.
|
||
| Top | |
||
| Lay3d_low |
|
|||
|
hmmm what about 3 inch?
_________________ Sexy Xe |
|||
| Top | |
|||
| huggiebear |
|
|||
|
3" should be ok. you might have to cut the thread off the u bolts once its attached.
|
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
are you able to get 3 inch blocks? ive seen 1,2,3,4, inch but ive only seen max 2.5 inch for EF EL waggons an utes
_________________ Sexy Xe |
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
i finaly decided to stop being lazy and get a photo of the hoodliner so far.
looks good at the very front, but crap for the rest cause its not all done. You do not have the required permissions to view the files attached to this post.
_________________ Sexy Xe |
|||
| Top | |
|||
| nato83 |
|
||
|
I dont know the legalities but surely you could get two blocks and weld them together and then get some u bolts made up to suit the length. Otherwise resetting the springs is the best choice and you can tell the guys what height you want it to sit and they will do it for you- can range between 300-500 depending if any bushes need replacing.
|
||
| Top | |
||
| Lay3d_low |
|
|||
|
yeh i was told theres a plaace in newcastle that will reset them for around 250-300. i should check that out actually, thatd be the best idea probly.
_________________ Sexy Xe |
|||
| Top | |
|||
| BenJ |
|
||
|
Agreed. I will be getting mine reset sometime this year.
I get a lot of axle tramp with the blocks. BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 22 guests |
