|
| mitchell g |
|
||
|
yeah thats true,
paint pen are the areas that require attention of strengthening as can be seen in the left hand side of the picture where it cracked when the bar took a heafty whack from a bump in the paddock when i was going to fast |
||
| Top | |
||
| mitchell g |
|
||
|
started fibreglass this afternoon, just waiting for the first layer to dry to apply the next layer to that area then move on, only doing an area at a time as we have to pull the screws out as we go cause they won't pull in and sit flush
|
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
{USERNAME} wrote: why make it something it's not full stop, it's a perfectly good looking car with the only alteration needed being the tickford bodykit, don't say it's to be original because it's not and nothings worse than an overkitted e series wannabe typhoon imo, especially with a stock setup. wtf man? the site is called FORDMODS |
||
| Top | |
||
| bry40l |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: why make it something it's not full stop, it's a perfectly good looking car with the only alteration needed being the tickford bodykit, don't say it's to be original because it's not and nothings worse than an overkitted e series wannabe typhoon imo, especially with a stock setup. wtf man? the site is called FORDMODS each to their own at least its not a flame kit, or a 30 bhp ebay chip
_________________ BF XR6 |
|||
| Top | |
|||
| mitchell g |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: why make it something it's not full stop, it's a perfectly good looking car with the only alteration needed being the tickford bodykit, don't say it's to be original because it's not and nothings worse than an overkitted e series wannabe typhoon imo, especially with a stock setup. wtf man? the site is called FORDMODS each to their own at least its not a flame kit, or a 30 bhp ebay chip that'd be fully sick brah |
||
| Top | |
||
| bry40l |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: why make it something it's not full stop, it's a perfectly good looking car with the only alteration needed being the tickford bodykit, don't say it's to be original because it's not and nothings worse than an overkitted e series wannabe typhoon imo, especially with a stock setup. wtf man? the site is called FORDMODS each to their own at least its not a flame kit, or a 30 bhp ebay chip that'd be fully sick brah top off the sully sick ebay chip and flame kit with an eletronic turbo 
_________________ BF XR6 |
|||
| Top | |
|||
| mitchell g |
|
||
|
it's be mental in the wet after that
|
||
| Top | |
||
| mitchell g |
|
||
|
went and picked up a tickford kit for my mates xr6 this morning and i've always had the idea of the door pod thing on with the typhoon kit, and making a mould of it and building it up away from to bring it out the right spot,
 i'm hoping to get the front bar completely fibre glassed before the rain today |
||
| Top | |
||
| bry40l |
|
|||
|
that will look good with the door piece once you get it built out to suit the side skirts, i was just pulling some stuff off my spare car for another fordmods member and it was sunny one minute and raining the next with thunder and lightning and came outta no where
 lucky i got everything off in time
_________________ BF XR6 |
|||
| Top | |
|||
| mitchell g |
|
||
|
yeah, we got a servier weather warning going around,
flash flooding and 150mm of rain exspected, had 600mm in 6 hours 3 years ago, got the fibre glass going from the front right corner to the numberplate moulding, not sure if i'll cut the height of the side skirt or build it up and leave it about 3/4 up the door, looks a little funny at that height |
||
| Top | |
||
| mitchell g |
|
||
|
this is as far as i'll get with fibreglassing today
 thinking of cutting the plastic away from behind this part 
|
||
| Top | |
||
| SWC |
|
||
|
Have you sanded the paint back to the plastic on the Fairmont bar and roughed the plastic? Also did you remove the primer and sand the fiberglass?
|
||
| Top | |
||
| mitchell g |
|
||
|
yes i did do that, then used wax and grease remover and wiped it with a clean rag then applied the resin to the bar then the fibreglass shet then dabbed the brush on the sheet and added a 2nd layer after it have dried
|
||
| Top | |
||
| Yes.40L |
|
|||
|
Fairmont typhoon kit FTW!!!
_________________ YES.40L |
|||
| Top | |
|||
| mitchell g |
|
||
|
yepp, you going to get proper typhoon skirts or the bitsa side skirts that phat customs produce ?
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 60 guests |
