|
| cjh |
|
|||
|
I got a liitle done today before I have lunch and head off to work.........
I made a g'box extension housing plug for the 4sp box i'll be using.....I don't have a spare slip-yoke. Then started on making the parts for the lefthand engine mount. You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
|||
|
More pics...................
The plate sitting on the K frame isn't alloy, it's a piece of 75mm x 5mm RHS...which just happens to be the right size and shape, the same as the bottom of the original engine mount. In the lathe chuck is a piece of Hollow bar that I will bore out to make the outer shell for the bushes. You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Mad2 |
|
|||
|
|
|||
| Top | |
|||
| cjh |
|
|||
|
{USERNAME} wrote: I'm starting to think about making a dizzy, using the guts from an XD electronic dizzy ( already have one of these), but using an EA to ED cap and rotor (I have heaps of these)......yet to do some measurements.....I need the cap to be large enough, so I don't get a high energy spark jumping to 2 terminals at once. The size limit will be how close it (the cap) will be to the block, and the inner guard of the car. I have a chunk of alloy round big enough to make a new dizzy body....and I have a bunch of genuine steel dizzy gears for a slant 6......just gotta work out a design. First things first.....make my engine mounts......I have made the bushing centre tubes from an old shockie shaft from a Commodore....22mm hard chromed shaft, with a 1/2" hole in the guts for a 1/2" UNC grade 8 CAT bolt.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Mad2 |
|
|||
|
if i remember correctly the hemi6 dizzy is close to the frame rail where as the /6 is a lot shorter
best of luck making up the dizzy ... will be watching to see how ya go  pics ..... pics .... pics  ohh .. how did ya hand go at work?? |
|||
| Top | |
|||
| cjh |
|
|||
|
{USERNAME} wrote: if i remember correctly the hemi6 dizzy is close to the frame rail where as the /6 is a lot shorter best of luck making up the dizzy ... will be watching to see how ya go pics ..... pics .... pics ohh .. how did ya hand go at work?? The hand isn't goin too bad....but, it does hurt when I use a hammer....and I haven't used a 3/4" tension wrench wound up a bit yet either, only used it on 230 ft/lb. Pics of the engine mount as of tonight............ I have modified an existing LH engine mount bracket....not yet finished reshaping....and finished machining the outer bush shells ( has 0.5mm crush on the bushes ).......added bonus, I found a piece of 75mm x 6mm flat bar about 700mm long tonight... .....that'll come in handy for the side plates of the mount.
You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
|||
|
Finally finished the LH engine mount....and started on the RH engine mount.
In the pics is an original bracket, and the modified one.....as yet unfinished in this pic. You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
|||
|
Here it is on it's way to finished......just need to blast it and paint it.
You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
|||
|
So.....before and after............
You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
|||
|
The RH engine mount is more difficult....not as easy to get to, and a little less room.
You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Matt_jew |
|
||
|
Awesome fabrication work!
_________________ {USERNAME} wrote: More people paid for a ride in a VT commodore then an AU Falcon so the VT is superior.
Based on that fact my Mum is the best around! |
||
| Top | |
||
| cjh |
|
|||
|
{USERNAME} wrote: Awesome fabrication work! Thank you.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| SWC |
|
||
|
That is some nice work.
Great to see real mods happening on a build other than sticking a sticker on or such. Keep up the great work. |
||
| Top | |
||
| cjh |
|
|||
|
Thanks SWC.
Today I built the RH engine mount....just needs blasting and painting....but for the moment they need to be in place to see about making a tailshaft loop. You do not have the required permissions to view the files attached to this post.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Mad2 |
|
|||
|
wished ya lived closer
 .... i'd sweep the floor afta ya .... and maybe learn a few things too  lollookin good |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 76 guests |
