|
| gasdea |
|
|||
|
{USERNAME} wrote: Who doesn't like smoking tyres?  Cheers ToranaGuy people who have expensive tyres? like me?
_________________ CHECK THIS s**t: LAWLZ |
|||
| Top | |
|||
| huggiebear |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: Who doesn't like smoking tyres? Cheers ToranaGuy people who have expensive tyres? like me? or people who live in a cat |
|||
| Top | |
|||
| TROYMAN |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: Who doesn't like smoking tyres? Cheers ToranaGuy people who have expensive tyres? like me? or people who live in a cat  live in a cat?? wtf..lol
|
||
| Top | |
||
| huggiebear |
|
|||
|
Location: garfield
VIC, Australia i thought someone would have looked at his location lol |
|||
| Top | |
|||
| fairlane6970 |
|
|||
|
I think most of us did!
 
_________________
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
woo hoo, clutch is in...
not after some dramas though.. fitted the clutch and all fit fine.. untill we started it.. with a schredclungclundglunch..  wtf...so it had to be pulled back out, to find that the folded edges on the lower section of the au sandwich plate was touching the flywheel, as the billet flywheel sits a few mm closer to the block compared to the std one.. ok. fixed that.. then went to start it again and clunkclunkclunickclickclick..  f**k!!!!pulled the box back out and the ba pressure plate was touching the webbing on the inside of the au bellhousing, grindie grindie all fixed now... its pretty obvious ford did not intend on anyone using a larger diameter than std.. so now to up the boost again, do some cruising and send it off for another dyno tune...... |
||
| Top | |
||
| Dansedgli |
|
||
|
Sounds like a painful day.
18psi tune? 
|
||
| Top | |
||
| TROYMAN |
|
||
|
not to painfull , atleast it was done in a workshop, i didnt do this one laying on a gravell driveway..
yea maybe 15 psi  i think 18 might be pushin it ..lol
|
||
| Top | |
||
| EDXR6-Poly |
|
|||
|
Did you take any pictures of the process?
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| TROYMAN |
|
||
|
na no pics, we did it at a friendly mechanics workshop near by..
|
||
| Top | |
||
| the sam |
|
||
|
NEED PICS!
_________________ LOW, LOUD AND LUMPY |
||
| Top | |
||
| TROYMAN |
|
||
|
{USERNAME} wrote: NEED PICS! need pics of what??? its just a gearbox going into the car and out and in ect ect..lol there are pics of the clutch and flywheel a page back.... |
||
| Top | |
||
| huggiebear |
|
|||
|
troy perhaps they want to see the angle grinder that did the grinding...
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
{USERNAME} wrote: troy perhaps they want to see the angle grinder that did the grinding... yea maybe, i didnt bother with pics this time.. if you have seen inside an au bellhousing there are re enforcing webbing all the way around the housing, just had to grind a 5mm 1/4 moon shape into the webing all the way around.. |
||
| Top | |
||
| Dansedgli |
|
||
|
Pics of SKIDS!!
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 26 guests |
