|
GeReN |
|
|||
|
Nice photoshop!
And the car looks great too, well done
_________________ Brand New Distributor: $50 + other stuffs |
|||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: Nice Photoshopping too --- How about finding a power aerial for it so you can tuck it away a little?
actually it does have a power antanna it just was in the up position... |
||
Top | |
TROYMAN |
|
||
|
i like the white on the bumpers now!!...thanks benj
|
||
Top | |
TROYMAN |
|
||
|
today i started adding bits for the bbm conversion..
i ran the wires through the firewall needed for bbm switch,knock sensor ect.. while i was at it i swapped the trip comp pwm wire over to the injector pwm wire and fitted the el ecu.. and as my car has cruise control there is a vacc module where the bbm solinoid is suposed to go.. so instead of re-locating the cruise controle vacc module i decided to mount the bbm switch to the firewall instead.. here are pics.. You do not have the required permissions to view the files attached to this post. |
||
Top | |
BenJ |
|
||
|
Troyman
Nice solution for the BBM switch. BenJ
_________________ {DESCRIPTION} - Current Ride |
||
Top | |
TerroristGHIA |
|
|||
|
So it is done? How does she drive now?
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: So it is done? How does she drive now?
Brett no its not finished yet ive run the wires and the ecu is in.. but i havnt swapped the manifold over yet. i should have it finished by tomorrow afternoon.. after fitting the cam it idled like crap with the std ed ecu.(hunting for idle,running rich)ect now with the el tickford ecu it idles great even with the log still fitted its a bit doughy down low(because of different fuel map) but when it gets to 3800rpm holy s**t!! it pulls like a horny school boy |
||
Top | |
TROYMAN |
|
||
|
well it all back together with the bbm now.
the only thing still to do is the cruise control cable and i think i need to advance the timing alittle. as it went from pulling like a horny school boy yesterday with the log manifold and el ecu, to going like a impudent old man today with the bbm and el ecu.. so i got a few bugs to iron out but its getting there.. You do not have the required permissions to view the files attached to this post. |
||
Top | |
ef_paddy |
|
||
|
Mate just went through the 8 pages of this thread... awesome work and i definitely reckon the bump strips would look aswesom white with the chrome strips... looks much more modern
_________________ "You only need 2 tools, WD-40 and duct tape. If it doesnt move and it should, use WD-40. If it moves and it shouldnt, use the duct tape!" |
||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: Mate just went through the 8 pages of this thread... awesome work and i definitely reckon the bump strips would look aswesom white with the chrome strips... looks much more modern
cheers thanks mate |
||
Top | |
TROYMAN |
|
||
|
today i modified the ed cruise controle cable by cutting the end off pulling the inner cable out and cutting the outer down to the right length..
then i got the el end of the cruise cable that i got from benj.(thanks ben ).i cut it down to the thick outer and removed the metal part of the outer and removed the inner. then i drilled into the el thick outer plastic and slid the ed outer cable into the el end and ran the ed inner through. i then found a small crimp and crimped the ed inner cable to the el cable end. and it works a treat!! sorry i didnt take any progress pics.. i know i should have! You do not have the required permissions to view the files attached to this post. Last edited by TROYMAN on Thu Nov 06, 2008 3:45 pm, edited 1 time in total. |
||
Top | |
TerroristGHIA |
|
|||
|
So, when are we going to do my ED??
I like the look of that. Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
huggiebear |
|
|||
|
that is looking good. anyone have a spare EF/EL cruise contol unit for me?
|
|||
Top | |
BenJ |
|
||
|
Hey Troyman
Now that is nice work. Taking my original concept and finessing it so it is much tidier than my bodgy job. Excellent!!!! Huggie He is using the ED vacuume cruise setup and modified the two different cables to work together. You can do this to mate. BenJ
_________________ {DESCRIPTION} - Current Ride |
||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: Hey Troyman
Now that is nice work. Taking my original concept and finessing it so it is much tidier than my bodgy job. Excellent!!!! Huggie He is using the ED vacuume cruise setup and modified the two different cables to work together. You can do this to mate. BenJ yes is was your way that what gave me the idea.. i did take a risk in cutting that el cable short but it all worked in the end.. |
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 18 guests |