|
KWIKXR |
|
|||
|
{USERNAME} wrote: ..so the car is booked in for a new exhaust system tomorrow as there is no cat on it at the moment so your glad your not my neighbour when i start the car at 730 am to drive it to the exhaust place straight out of the extractors lol.... i might post a sound clip when its done? Please do, i wanna hear this new 3" exhaust The painted extractors look good by the way. Going by your sig, after the exhaust gets done, you might get lucky and gain 6+kw's to crack the 200 mark |
|||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: are the extractors still shiny not quite! as the paint is a matt finish but they are still the same colour so the paint is still there.. |
||
Top | |
frankieh |
|
|||
|
what made you part with the genies? they actually have a 3 inch collector... I took my pacie's out and put the genies in because I couldn't get the gas install over the pits as it was to close to the extractors and I run out of time..
|
|||
Top | |
TROYMAN |
|
||
|
i took the genie's off because the 4 bolt flange half way up keeps leaking since ive put the supercharger on and the engine pipes collect at that flange.
also the genies are press bent and the pacies are mandrel bent. also seeing as most people say that the pacies are best well ill see for my self.?. i was going to weld the flange up on the genies but i would have had to take them off anyway and thought ill see if the pacies are any better.. on the down side it looks like the genies are stainless steel and the pacies are only mild steel? |
||
Top | |
shav |
|
|||
|
stainless or mild steel, I reckon the paccies are better for flow.
Will you get the car re-tuned with the new headers? I recommend it.
_________________ Cheers |
|||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: stainless or mild steel, I reckon the paccies are better for flow. Will you get the car re-tuned with the new headers? I recommend it. yea it needs to be re tuned due to operational hickups with the way the ecu was set up.. so i thought ill do the exhaust before the re tune! |
||
Top | |
frankieh |
|
|||
|
Thats interesting... my genies are definatly not press bent.. but they look similar in every other respect.. does yours have the chrome genie batch bolted to them?? I ask because I didn't think genie did anything press bent under the name genie..
I made a copper gasket for the four bolt flange and layered it with exhaust gasket goo before bolting it tight.. have yet to see how it does under boost pressures, but I'm hopeful.. didn't notice any difference in power swapping between pacies and genies.. but the genies sound better... deeper and more husky.. My genies have a 3 inch collector which is bolted to a 3 inch magnaflow and then shrunk down to 2.5 inches for the rest of the trip.. will be interesting to see how it goes under boost. |
|||
Top | |
XRfairmont67 |
|
|||
|
hey, the extractors came up nice troy
|
|||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: Thats interesting... my genies are definatly not press bent.. but they look similar in every other respect.. does yours have the chrome genie batch bolted to them?? I ask because I didn't think genie did anything press bent under the name genie.. I made a copper gasket for the four bolt flange and layered it with exhaust gasket goo before bolting it tight.. have yet to see how it does under boost pressures, but I'm hopeful.. didn't notice any difference in power swapping between pacies and genies.. but the genies sound better... deeper and more husky.. My genies have a 3 inch collector which is bolted to a 3 inch magnaflow and then shrunk down to 2.5 inches for the rest of the trip.. will be interesting to see how it goes under boost. yep there genies they had the chrome genie badge on top untill recently. maybe they are early ones? its hard to tell as being stainless there are no signs of age except for heat burn.. |
||
Top | |
TROYMAN |
|
||
|
{USERNAME} wrote: hey, the extractors came up nice troy thanks mate |
||
Top | |
LP_ |
|
||
|
Quote: So is the exhaust done? BenJ I can post in the right topic Is it done yet or still waiting for the 3" bends |
||
Top | |
Froudey |
|
||
|
Hey troyman I sent a PM regarding you old extractors...
the pacies look good, does it sound like a tractor when ya start her up lol.
_________________ R.I.P Tobias my son. |
||
Top | |
TROYMAN |
|
||
|
yep it definatly did sound like a truck of some kind lol...
here is a clip i took early thismorning on the way to the exhaust shop just for kicks.. if your pc has normal speaker it will probably just distort..lol http://www.youtube.com/watch?v=js-FzPLGZHA the exhaust is done.. the guy had fitted it without a resinator first and it was way too loud.. so he fitted a resinator and is much better but still fairly loud.. here is a pic as it was being fitted.. Attachment: DSC01462.JPG the exhaust note is a fair bit deaper than before.. so far the car responds better with the 3" but i havnt really opend it up yet.. You do not have the required permissions to view the files attached to this post. Last edited by TROYMAN on Sat Jul 18, 2009 8:45 am, edited 1 time in total. |
||
Top | |
LP_ |
|
||
|
looking
|
||
Top | |
BenJ |
|
||
|
NICE!!!!!!!
So we up for a cruise? BenJ
_________________ {DESCRIPTION} - Current Ride |
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 10 guests |